Call Us Now

1800 234 477

Height Safety

Aegis safety have been designing and installing fall prevention systems for over 30 years. These systems include horizontal and vertical cable systems, Roof safety systems, Horizontal rail systems, anchor points, Handrails, walkways, ladders, staircases etc. Contact our specailist team for further information.


Aegis Sales & Service offer a range of calibration options within our workshop or onsite by arrangement.



Aegis Sales & Service is a teir 1 service facility for BW Technologies by Honeywell Analytics. We can provide both workshop and onsite calibrations for portable gas detection and all gases used are NATA traceable.
Our workshop calibration turn-around [our workshop is staffed by 2 fulltime Technicians. Our 48hr turnaround policy is for Calibration only (unless repairs have been pre-approved and parts are in stock). On occasion this time frame may be extended when the workshop is busy.] is 48hrs. An 'Urgent turn-around' option is also available if required [a surgcharge applies].
Gas detectors are an important part of your personal safety and have been designed to alarm when gases are beyond an acceptable limit. Your personal safety alone is enough of a reason to make sure that you have your detector calibrated and serviced according to Australian Standards and the Manufactuer's specifications. Why Should you Challenge (Bump) Test your gas detector? Check out our Challenge information.
Contact our office on 07 3865 1139 if you would like one of our Technicians to attend your site to carry out calibration and service on your equipment.
We can service and calibrate all types of portable gas monitors including:
Honeywell GasAlert MicoClip, Quattro, Max XT, Micro 5 Sales, Calibration & Service MultiRAE portable gas detector by RAE Systems Sales, Calibration & Service Calibration of Honeywell Impact Pro portable gas detector Calibration of MSA personal gas detectors Calibration of Riken Keiki portable gas detectors Drager portable gas detector sales, calibration & service
BW Technologies  RAE Systems  Honeywell  MSA RKI  Drager



Our team of technicians can calibrate, repair and maintain all leading brands of gas detection equipment within our dedicated workshop or we can provide onsite solutions for permanently installed systems including [but not limited to] carpark gas detection, refrigerant leak monitors, controllers, flame detection and toxic sensors. 

 Sentech Refrigerant Monitor Sales & Calibration Australia  Honeywell Sensepoint Sales, Calibration & Service  AmpControl Micro 4000 Controller Sales & Calibration  Catalytic and Infrared Gas Detector Calibration & Sales  Gas Detection Calibraion of Catalytic Sensors AmpControl iQguard Toxic Gas Detection TVOC ATEX certified to zone 2 without safety barriers
SenTech Honeywell Controllers Flame Detection Sensors AmpControl Ion Science


At Aegis Sales & Servcie we can calibrate a range of pressure and vacuum devices.

Many techniques have been applied and developed to measure pressure and vacuum. Aegis Sales & Service has partnered with Additel and Rhomberg Instruments to bring you  quality equipment to suit your needs. 

Additel Pressure Sales, Calibration & Service Rhomberg Pressure Gauge Sales, Calibration & Service
Additel Rhomberg


Our expertise in temperature measurement and monitoring is unparalled. Our highly skilled team is trained in process control, automation and PLC programming. In-house or onsite calibrations are available. 

Intech Transmitter Sales, Calibration & Service Intech IN P Transmitter  Intech RTD Temperature Probe Calibration Intech Multiplexer Sales, Calibration & Service
Transmitters Processors RTD Probes Multiplexers



Aegis Sales & Service can install, upgrade and maintain existing circuits and systems to suit your needs. As licensed electrical contractors we can take care of your electrical installation and maintenance requirements. We also have Hazardous Area qualified personnel.

Electrical Testing & Tag, 

Electrical Equipment Test and Tag Multimeter Calibrations - fluke LV Rescue Kit Inspections Electrical Gloves Inspections Hazardous Area Certified Electricians
Test & Tag Multimeter LV Rescue Kits Electrical Goves Hazardous Area


WinGrip Calibration

The Latchways WinGrip is a vacuum anchor fall protection system that is used for aviation maintenance and manufacturing.   

Latchways Wingrip Calibration & Service   Latchways Wingrip Calibration & Repair

Breathalyser Calibration

The reliability of your Breathalyser is very important. To ensure it's ongoing accuracy and reliability of your Breathalyser it should be calibrated every 6 to 12 months [as per Australian Standards and or manufacturer's recommendations]. 

Aegis Sales & Service is an authorised Calibration centre for Alcosense Breathalysers by Andatech.

For more information and pricing on Breathalyser Calibrations visit our Breathalyser Shop.

breathalyser alcosense volt 1 Industrial Breathalyser Calibration - Australia - AlcoSense by Andatech Wall Mounted Commercial  Breathalyser Calibration - Australia - AlcoSense by Andatech
Personal Breathalyser  Industrial Breathalyser Fixed Wall Mount Breathalyser

Visit Our Showroom

1/119 Delta Street Geebung, QLD 4034

Phone: 07 3865 1139


Business Hours

Mon - Fri -------------- 8:00am to 4.30pm

Sat - Sun ------------- Closed

Join Us

Follow Aegis Sales & Service on Facebook   Connect with Aegis Sales & Service on Linkedin  Connect with Aegis Sales & Service on Google Plus



Line Marking Equipment Quote Request

Tell what you are interested in or your application and we will help with the best option for your needs.


Please select the required application and equipment interests

We can also have your line marker repaired. Call us today to organise your line marker repair.

Portable Gas Detector Warranty Registration

Warranty Registration - Gas Detection

Warranty Registration - Portable Gas Detector

Register your Portable Gas Detection


Warranty Registration - Sentech Refrigerant Monitor

To validate the Warranty on your Sentech Refrigerant Monitor please complete this form and submit to return it to Aegis Sales & Service / Techinspect within 30 days of installation.

Please provide the relevant system information: Installation Address, Company Name and/or Building Name, Sentech Model and Serial Number.


Please provide required information on the installation of the system.


I hereby certify that the above SenTech equipment has been installed and inspected in accordance with the installation and operation manual and is in satisfactory operating condition.


Book Your Loner Demo

Book your Lone Worker Device Demonstration


Simply complete this form and one our qualified staff will contact you or phone the office on 1800 234 477.


Contact Us - Roof Safety Systems

Simply complete this form and one our qualified staff will contact you or phone the office on 1800 234 477.


Contact Us - Roof Safety Systems - Latchways

Please complete the details below and one of our Roof Safety Professionals will be in contact to discuss your system needs.


Simply complete this form and one our qualified staff will contact you or phone the office on 1800 234 477.